Product ID:INTERGARD 264, FPD052
MSDS Date:04/20/1999
FSC:8010
NIIN:01-271-9722
Status Code:A
MSDS Number: CLNMN

INTERNATIONAL PAINT INC

6001 ANTOINE DRIVE
HOUSTON, TX 77091
US

Emergency Phone: 800-854-6813

Info Phone: 713-684-1244

Preparer: ERNEST CARTER

Cage: 0TZS5

INTERNATIONAL PAINT INC

HOUSTON, TX 77091 US

Telephone: 713-684-1244

Cage: 0TZS5

EPOXY RESIN

CAS: 25068-38-6

RTECS: CE6880000

MAGNESIUM SILICATE HYDRATE

CAS: 14807-96-6

RTECS: WW2710000

OSHA PEL see Table Z-3

ACGIH TLV: 2 MG/M3

MICA

CAS: 12001-26-2

RTECS: VV8760000

ACGIH TLV: 3 MG/M3

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3

ACGIH TLV: 10 MG/M3

METHYL N-AMYL KETONE

CAS: 110-43-0

RTECS: MJ5075000

OSHA PEL 465 MG/M3;100 PPM

ACGIH TLV: 233 MG/M3;50 PPM

EPOXY RESIN

CAS: 25036-25-3

BENZYL ALCOHOL

CAS: 100-51-6

RTECS: DN3150000

AROMATIC HYDROCARBONS

CAS: 64742-95-6

RTECS: WF3400000

TRIMETHYLBENZENE

CAS: 25551-13-7

RTECS: DC3220000

ACGIH TLV: 123 MG/M3;25 PPM

AMORPHOUS SILICA

CAS: 7631-86-9

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: VAPOR HARMFUL. MAY AFFECT
THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHES OR NAUSEA.
CAUSES NOSE AND THROAT IRRITATION. EYE CONTACT: CAUSES EYE
IRRITATION. SKIN CONTACT: CAN BE AB SORBED THROUGH THE SKIN. MAY
CAUSE ORGAN DAMAGE. CAUSES SKIN IRRITATION. MAY CAUSE ALLERGIC SKIN
REACTION OR SKIN SENSITIZATION. INGESTION: MAY BE FATAL IF
SWALLOWED AND MAY CAUSE ORGAN DAMAGE.
Medical Cond Aggravated by Exposure:

First Aid:INHALATION: REMOVE TO FRESH AIR. IF DISCOMFORT IS PRESENT OR
BREATHING ABSENT, GET MEDICAL ATTENTION. EYE CONTACT: FLUSH
IMMEDIATELY WITH PLENTY OF WATER FOR 15 MINUTES UNTIL IRRITATION
SUBSIDES.IF IR RITATION PERSISTS, GET MEDICAL ATTENTION.SKIN
CONTACT: FLUSH WITH LARGE AMOUNTS OF WATER. USE SOAP IF AVAILABLE.
REMOVE CONTAMINATED CLOTHING AND WASH BEFORE REUSE. GET MEDICAL
ATTENTION. INGESTION: I F SWALLOWED. DO NOT INDUCE VOMITING. KEEP
AT REST. GET MEDICAL ATTENTION.

Flash Point:=47.3C, 117.1F
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT, SPARKS, ELECTRICAL
EQUIPMENT AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. IN THE ABSENCE OF ELECTRICITY, A WATER
SPRAY (A FOG NOZZLE IS PREFERRED) MAY BE USED TO COOL CONTAINERS.
DECOMPOSITION AND COMBUSTION PRODUCTS MAY BE TOXIC.

Spill Release Procedures:CONTAIN SPILLED LIQUID WITH SAND OR EARTH.DO
NOT USE COMBUSTIBLE MATERIALS SUCH AS SAWDUST, ABSORB SPILL WITH AN
INERT MATERIAL (E.G. DRY SAND OR EARTH), THEN PLACE IN A CHEMICAL
WASTE. CONTAINER.

Handling and Storage Precautions:KEEP CONTAINER CLOSED.LOOSEN CLOSURE
CAUTIOUSLY BEFORE OPENING. STORE IN A COOL, WELL VENTILATED PLACE
AWAY FROM INCOMPATIBLE MATERIALS.KEEP AWAY FROM HEAT, SPARKS AND
FLAMES, PROTECT MATERIAL FROM DI RECT SUNLIGHT. GROUND AND BOND
CONTAINERS WHEN TRANSFERRING MATERIALS. EMPTY CONTAINERS MAY RETAIN
H

Respiratory Protection:DO NOT BREATHE VAPORS OR SPRAY MIST. IF YOU
EXPERIENCE EYE WATERING, HEADACHE OR DIZZINESS OR IF AIR MONITORING
DEMONSTRATES VAPOR/MIST LEVELS ARE ABOVE APPLICABLE LIMITS, WEAR AN
APPROPRIATE, PROPERL Y FITTED RESPIRATOR (NIOSH APPROVED) DURING
AND AFTER APPLICATION. FOLLOW RESPIRATOR MANUFACTURE'S DIRECTIONS
FOR RESPIRATOR USE.
Ventilation:PROVIDE SUFFICIENT VENTILATION.
Protective Gloves:WEAR CHEMICAL RESISTANT GLOVES.
Eye Protection:SAFETY GLASSES, CHEMICAL GOGGLES AND /OR A FACE SHIELD.
Work Hygienic Practices:USE BODY PROTECTION TO AVOID CONTACT WITH
PRODUCT.
Supplemental Safety and Health

Boiling Pt:=148.9C, 300.F
Vapor Density:HEAVIER
Spec Gravity:1.738
Evaporation Rate & Reference:SLOWER/ETHER
Appearance and Odor:LIQUID

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:FUMES MAY PRODUCE CARBON DIOXIDE AND
CARBON MONOXIDE. WELDING MAY PRODUCT CARBON DIOXIDE AND CARBON
MONOXIDE.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.